• Breaking News

    Sunday, December 13, 2020

    Home Unlabelled Wood carving Easy Beginner Snowman Tutorial - Carved With A Single Knife

    Wood carving Easy Beginner Snowman Tutorial - Carved With A Single Knife

    December 13, 2020

    Wood carving Easy Beginner Snowman Tutorial - Carved With A Single Knife

    Easy Beginner Snowman Tutorial - Carved With A Single Knife

    Posted: 13 Dec 2020 05:39 AM PST

    Before oil, after oil outside, after oil inside.( OC carving)

    Posted: 12 Dec 2020 09:42 PM PST

    Walnut wood spirit. Bit too dark may have to try a different finish but enjoyed making it.����

    Posted: 13 Dec 2020 03:38 AM PST

    20 Santa carvings later there’s been some improvements made.

    Posted: 13 Dec 2020 09:13 AM PST

    Basswood "Spirit" Animal Ornaments I made for my Friends

    Posted: 13 Dec 2020 05:28 AM PST

    I’ve been facinated with woodcarving and sculpting since I was a kid. Recently got a set of Pfeil tools as a gift and have now completed my first practice project.

    Posted: 12 Dec 2020 12:25 PM PST

    My happy place

    Posted: 13 Dec 2020 09:39 AM PST

    1st ever carving, I’m not sure how to finish/seal it. Any guidance?

    Posted: 12 Dec 2020 12:55 PM PST

    Looking for some beginner's advice on which tools to carve out the lettering in these photos. I want to get my dad a wood carving knife/whittling set for christmas, but I'm a bit lost!

    Posted: 13 Dec 2020 06:23 AM PST

    Rasping End Grain, Yay or Nay?

    Posted: 13 Dec 2020 08:49 AM PST

    I'm trying to get rid of some end grain off the end of my carving so I can focus on the carving. I was wondering if I should resume whittling it down with the aid of a gouge or if I should just rasp it off.

    submitted by /u/projectilebirb
    [link] [comments]

    Carving On Woodturning

    Posted: 13 Dec 2020 07:40 AM PST

    My first wizard! The eyes were the most difficult part for me. I don't want to paint it, I'm afraid that I'm going to mess it up.

    Posted: 12 Dec 2020 12:38 PM PST

    My first carving with a Dremel, a little push dagger carved out of teakwood. It currently has a 400-grit finish. Would love to hear some suggestions for the finishing !! Hope you all like it

    Posted: 13 Dec 2020 05:49 AM PST

    Been practicing doing some gnomes the past few days. I have tons of 1x1x6 basswood pieces and am running out of ideas of what to do. Any thoughts?

    Posted: 12 Dec 2020 06:08 PM PST

    I love Christmas! Also very addicted to carving now.

    Posted: 12 Dec 2020 01:52 PM PST

    Hand Carved Owl

    Posted: 12 Dec 2020 01:33 PM PST

    Challenge: recreate this ancient carving. Might be fun.

    Posted: 12 Dec 2020 03:28 PM PST

    Saw someone post a rocket recently.

    Posted: 12 Dec 2020 01:14 PM PST

    2nd “keeeper” carving. Snowman for my kid for Christmas. Wire hanger for arms. Leaving unpainted so that they can decide what to do with it.

    Posted: 12 Dec 2020 12:49 PM PST

    Sawdust the snowman

    Posted: 12 Dec 2020 06:32 PM PST

    Instruction before cutting with a circular saw. ⭕Examine the saw ��Before using the circular saw each time check the saw for safety. ��Check the blade for broken or damaged teeth, if any damage is found replace it. ��Check the power chord for cracks in the corded circular saw. ��Make sure the batte

    Posted: 12 Dec 2020 08:57 PM PST
    Read more
    at

    No comments:

    Post a Comment